Crestron NovaStar H Series Driver
✨ New🚀 Early AccessCrestron SIMPL+ module for NovaStar H Series video wall splicers (H2, H5, H9, H15, H20): preset recall, fade to black, freeze, brightness and audio, with layer and screen feedback over UDP.
🚀 Early Access: an untested release. It may have bugs or missing features and will change before 1.0. Sales are final. Your license includes 1.0 and every later update.
Screenshots
Overview
Recall presets from 16 buttons or by any preset ID, fade to black, freeze, clear the screen, set and save brightness, and set volume and mute. One monitored layer can be frozen and its source read. A raw command input reaches the rest of the protocol.
Feedback shows the monitored layer's source, input, position, size and freeze state, the screen's layer list, and the screen and splicer details and preset names when the processor receives them. A Device ID check reports a splicer that is not the one configured. The module counts the splicer as connected from its first answer, reports it lost after three unanswered requests, and keeps asking.
The download includes the SIMPL+ module (.usp and .ush), a sample SIMPL Windows program, an HTML5 touch panel, a join reference and the manual. Built for 3-Series and 4-Series processors. The splicer's Device ID, screen IDs and preset IDs come from its web page. The protocol has no power command and no input routing, and RS-232 is not supported in this release. A 30-minute trial runs on every program start, and activation uses an offline code, so the processor needs no internet connection.
Features
A SIMPL+ module for NovaStar H Series video wall splicers (H2, H5, H9, H15, H20): preset recall, fade to black, freeze, brightness and audio on one selected screen, with the splicer's own feedback where it can be read. It speaks the H Series control protocol, JSON over UDP port 6000. One module per splicer. The protocol has no power command and no input routing.
Control
- Presets: 16 preset buttons, or any preset ID from an analog
- Fade to black, freeze, clear screen, brightness (and save), volume up/down/set, mute
- Commands go to the screen selected when the module takes them, in the order they were made
- One monitored layer: freeze, and its source (not yet confirmed on a real splicer)
- A raw command input for other commands of up to 255 characters
Feedback
- The monitored layer: source, input, position, size, freeze; the screen's layer list
- Screen and splicer details and preset names when the processor receives them (they are large answers; a 4-Series discards an answer over 4096 bytes); otherwise the values this module set and the splicer accepted, with a signal for each saying which
- The last preset this module loaded (the protocol has no read of the current preset)
- A Device ID check that reports a mismatch
Connection
- Local network only.
- UDP: there is no connection to lose. The module counts the splicer as connected from its first answer and as lost after 3 requests in a row go unanswered, and keeps asking; it re-opens its socket only after 20 s of requests held waiting, or after 3 failed sends.
- Diagnostics on the module's own signals: connection status, last command, last response, last error, and traffic counters.
Licensing
- 30-minute trial on every program start; no code needed to evaluate.
- Licensed builds activate with an offline activation code from the AchKayEm licensing portal. The processor needs no internet connection.
- The license is meant to be stored on the processor and checked again on every start; storage on a processor is still to be confirmed.
Requirements. A NovaStar H Series splicer with a fixed address, reachable from the processor over UDP port 6000 in both directions; its Device ID, screen IDs and preset IDs (from its web page). A Crestron control system programmed in SIMPL Windows; the module is built for 3-Series and 4-Series (compiled for both; this release's code ran on a 4-Series against an emulator; not yet run on a 3-Series). RS-232 is not supported in this release.
Version history
Beta Pre-release
